简单分析一下油脂浸出设备中蒸脱机的产品介绍
油脂浸出设备；简略分析一下油脂浸出设备中蒸脱机的商品介绍：
A brief analysis of the oil extraction equipment in the evaporation of the goods:
蒸脱机是浸出油厂湿粕脱溶和钝化粕中抗养分因子的关键设备。如今商场的蒸脱机在多年实习的指导下完善的新式设备，集脱溶、干燥、冷却于一体，操作简略，商品质量安稳：
DTDC is a key equipment of anti nutrient factors in extraction plant wet meal desolventizing and passivation meal. Today's shopping malls in the evaporation of the practice of many years under the guidance of the new equipment, set out to dissolve, dry, cooling in one, the operation is simple, product quality is stable:
1透汽盘规划，使混合汽体由蒸脱层上行时均匀穿透料层，且不使湿粕从汽孔中落下，混合汽体气相温度可降至700C，不只脱溶效果好，而且节省了很多直接蒸汽量，减轻了冷凝器的冷凝负荷;
1. Unique vapor through the site planning, the vapour mixing by evaporation layer uplink uniform penetration material layer, and the wet meal from the steam holes flagged, mixed steam vapour phase temperature can be reduced to 700C, not only de dissolving effect is good, and saves a lot of direct steam quantity, reduce the condenser load;
2.蒸脱层的落料，选用主动控制的落料阀，确保了稳定的蒸脱层料位和满足的脱溶时刻，而且把蒸脱层和下部烘干层分隔，避免了生产中少量溶剂气体下行形成的损耗;
2 steam stripping, the selection of active control of the blanking valve, to ensure the stability of the steam stripping layer and meet the dissolution time, but also to the evaporation layer and the lower part of the dry layer, to avoid the formation of a small amount of solvent gas in the formation of the loss;
3.蒸脱机主轴选用一固定轴承固定上轴头和一推动轴承固定下轴头。避免了把大轴和搅刀的分量以及物料滚动的反作用力都下压到减速机上，形成减速机损坏、寿数不长和能耗耗费大等。用滚动轴承把上轴头固定在蒸脱机外部，一旦损坏替换十分简单;
3 DTDC optional spindle fixed bearing fixed on a shaft and fixed shaft bearing drive. To avoid the shaft and the stirring knife component and material rolling reaction are under pressure to the reducer, the formation of gear reducer is damaged, life is not long and the energy consumption of large consumption of. With the rolling bearing on the head is fixed in the external DTDC, once damaged replacement is very simple;
4.先进的主动料门系统，全滚动轴承规划，运转灵敏，寿数长，定位好，有用避免了溶剂外泄。蒸脱机上部的湿式捕集器选用进口的雾化喷头，把蒸脱机外排的混合气体中细微粕粉很多的捕集，有利于一蒸的换热效果，避免了粕粉进一步由一蒸进入分水箱导致的一系列问题。
4. Advanced active material door system, the rolling bearing planning, movement sensitivity, long life, good location, effectively avoid the leakage of solvent. On the top of the steam trap, the inlet of the wet collector is used, which is the most of the collector, which is beneficial to the heat transfer effect and avoids the series of problems caused by a steam into the water tank.
